目前市場上有很多比較出名的酒類，那么這些酒是如何釀造出來的，其實它們都是需要釀酒設備來釀造的，釀酒設備在整個釀酒過程中發揮著很大的作用，那么
全自動涼茬機廠家就來講講釀酒設備涼茬機電機使用前的檢查方法。
At present, there are many well-known brand wines in the market. How are these wines brewed? In fact, they all need brewing equipment to brew. The brewing equipment plays a great role in the whole brewing process. Then, the automatic stubble cooler manufacturer will talk about the inspection method before the use of the stubble cooler motor of the brewing equipment.
1、用壓縮空氣或手動吹風機吹凈電動機內部灰塵、電刷粉末等，污垢雜物。
1. Use compressed air or manual blower to blow out the dust and brush powder inside the motor and remove dirt and sundries.
2、拆除與電動機連接的一切接線，用絕緣電阻表測量繞組對機座的絕緣電阻。若小于0．5MΩ時，應進行烘干處理，測量合格后再將拆除的接線恢復。
2. Remove all wiring connected to the motor and measure the insulation resistance of the winding to the base with an insulation resistance meter. If it is less than 0.5m Ω, it shall be dried and the removed wiring shall be restored after the measurement is qualified.
3、檢查涼茬機換向器的表面是否光潔，如發現有機械損傷或火花灼痕應進行必要的處理。
3. Check whether the surface of the commutator of the stubble cooler is smooth and clean. If any mechanical damage or spark burn is found, necessary treatment shall be carried out.
4、檢查電刷是否嚴重?fù)p壞，刷架的壓力是否適當，刷架的位置是否位于標記的位置。
4. Check whether the brush is seriously damaged, whether the pressure of the brush holder is appropriate, and whether the position of the brush holder is at the marked position.
5、根據涼茬機電動機銘牌檢查直流電動機各繞組之間的接線方式是否正確，電動機額定電壓與電源電壓是否相符，電動機的起動設備是否符合要求，是否完好無損。
5. According to the motor nameplate of the stubble cooler, check whether the wiring mode between the windings of the DC motor is correct, whether the rated voltage of the motor is consistent with the power supply voltage, and whether the starting equipment of the motor meets the requirements and is intact.
平時我們在使用釀酒設備的時候也要注意設備的參數，注意添加機油，保證設備能夠正常的使用，后主要的是釀酒設備的出料的密封圈是易損部件，所以我們要注意檢查，發生損壞要及時進行更換；
Usually, when we use the brewing equipment, we should also pay attention to the parameters of the equipment and pay attention to adding oil to ensure that the equipment can be used normally. After that, the main thing is that the sealing ring of the discharge of the brewing equipment is a vulnerable part. Therefore, we should pay attention to inspection and replace it in time in case of damage;
定期清理酒釀設備是必須的，但是要注意避免有硬物刮傷設備，對于有些污染物我們可以使用酒精來進行擦拭；定期對設備的內部件進行清洗，清洗完成之后好要用壓縮空氣將其吹干。平時在使用設備的時候，要嚴格按照說明書上的進行操作。關注我們
http://m.tersatig.cn，了解更多事項！
It is necessary to clean the brewing equipment regularly, but it is necessary to avoid scratching the equipment by hard objects. For some pollutants, we can use alcohol to wipe them; Clean the internal parts of the equipment regularly, and blow them dry with compressed air after cleaning. When using the equipment at ordinary times, strictly follow the instructions. Follow us http://m.tersatig.cn Yes, learn more!
自動售酒機 2024-07-25 
